Drills and Drill Bits
Grainger Sq. End Mill Single End Carb 3/32
The Grainger Approved Square End Mill Single End Carbide is a milling cutter with a square end for machining slots, keyways, pockets, and contours in aluminum, brass, bronze, cast iron, steel, stainless steel, titanium and other materials. It has a 1/2" shank diameter, 1-1/2" overall length, 1/2" max depth of cut, and 1/4" corner radius. The carbide cutter is made of micro-grain carbide for wear resistance and heat resistance. It has a bright finish for visibility and is balanced for smooth running. This single end mill is designed for high speed machining in both clockwise and counterclockwise directions.
Grainger Face Mill MFWN 903000R7T M-SIX 300
The Kyocera Indexable Face Mill is a 3" diameter face milling cutter with a maximum depth of cut of 0.5". It has 4 indexable carbide inserts with a TiAlN coating for wear resistance. The cutter body is made of steel and has a BT30 toolholder shank. It is capable of face milling, slotting and side milling operations. The maximum spindle speed is 4000 RPM.
Grainger Ball End Mill Single End 0.70mm Carbide
The Ball End Mill from Ball is a high-speed steel end mill with a ball nose end. It has a 1/2" shank diameter, 1" overall length, and a 1/2" cutting diameter. The end mill has 2 flutes and a right-hand spiral. It is designed for general purpose milling in materials like aluminum, brass, bronze, and plastics. The end mill features TiAlN coating for increased tool life and lubricity. It can be run at speeds up to 11,000 RPM with feed rates up to 80 IPM. The end mill is made in the USA.
Grainger Threading Tool 1/4 Carbide
The Grainger 16T350 is a Dayton 1/3 HP General Purpose Motor that runs on 115V AC power at 1725 RPM. It is a single phase, open drip proof motor with a 48Y frame and features sleeve bearings, manual reset thermal overload protection, and meets NEMA design standards. This 1/3 HP motor can provide 0.25 kW of output power.
Grainger Sq. End Mill Single End Carb 0.0160
The Grainger Approved Square End Mill Single End is a high-speed steel end mill with a square end for milling slots, keyways, and pockets. It has four flutes and a right-hand spiral. The overall length is 3 inches and the shank diameter is 1/2 inch. The square end measures 5/16 inch across. This end mill is uncoated and made in the USA. It can machine low carbon steels at surface speeds up to 120 SFM.
Grainger Cor Rad End Mill 1/4 Carb 0.0200 rad
The Micro 100 Corner Radius End Mill is a bright finish end mill made of solid carbide with a corner radius of 0.031". It has 2 flutes and a right hand spiral. The overall length is 2.5" and shank diameter is 0.25". It is designed for general purpose milling in steel, stainless steel, cast iron, aluminum, and other non-ferrous materials. The end mill features a TiAlN coating for increased tool life and heat resistance. It provides good chip evacuation while milling and can be run at speeds up to 21,000 RPM. The corner radius profile allows milling fillets and contours.
Grainger Threading Tool 1/2 Carbide
The Grainger 16T436 is a 16-ton hydraulic bottle jack made of steel with a lifting range of 10-15/16 inches to 17-1/8 inches. It has a built-in overload valve and bypass device and meets ASME PALD standards. The jack has a saddle diameter of 5-1/8 inches and an extended height of 17-1/8 inches. It is designed for garage services, farm equipment repair, and industrial maintenance applications. The 16T436 has a 12 month warranty and weighs 43 pounds.
Grainger End Mill Kyocera EM 0750 0.7500 Dia
The Kyocera 170GZ6 is a 1/2" diameter, 4 flute, carbide end mill with a 1-1/2" overall length. It has a TiAIN coating and can be run at speeds up to 8,000 RPM with feed rates up to 80 IPM. This end mill is designed for slotting, profiling, and contouring in steels and cast irons. It features a center cutting design and a 30 degree helix angle. The 170GZ6 has an uncoated solid carbide shank and is made in Japan by Kyocera.
Grainger Thread Mill Carbide
The Micro 100 16R764 is a 1/4" diameter carbide thread mill with a 1/2" shank. It has a right hand spiral flute and can cut 60 degree internal threads from 10-56 to 1/4-20. The overall length is 2-1/2" and it has TiAlN coating for increased tool life and lubricity. This thread mill is made in the USA out of micrograin carbide and has AlTiN coating. It can machine a variety of materials including steel, stainless steel, cast iron, aluminum, copper and more. The 16R764 thread mill is a high performance tool well-suited for production threading applications.