Tubing Connectors and Fittings
Microsolv Technology Corporation Tubing Connector Fittings, High Pressure, Two Pieces, 1/16", PEEK, Natural, Large Head, Standard Length and 10-32 Screw Threads. Use with Double Cone Ferrules. Finger Tighten, 1 EA.
These Two Piece, "Male Nuts" are used to connect PEEK or Stainless Steel tubing in the high pressures zones of HPLC systems. This fitting has a 12mm diameter knurled head, 18mm total length (top to bottom) and requires a Double Cone, Ferrule, sold separately. 2 Piece Male Nuts are often chosen because they can be used at slightly higher pressures compared to 1 Piece Nuts. The required, Double Coned Ferrules will swage tubing at two places and have a greater grip than one piece fittings. The larger Head makes it easier to produce the torque needed to achieve a good connection. As Ferrules wear down, they need to be replaced. This Nut can be reused with new Ferrules.
Microsolv Technology Corporation Tubing Connector Fittings, Low Pressure, 1/8", Polypropylene, White with 1/4-28 Screw Threads, for use with flanged, polymeric tubing. 10/PK.
These "Male Nuts" are used to connect polymeric tubing in the low pressures zones of HPLC systems and other low pressure, fluidic uses. Tubing must be flanged and Washers are required to work properly, and sold separately.
Microsolv Technology Corporation Union, Connector, Low Pressure, with 1/4-28 Screw Threads. Nylon. 1 EA.
This "Union" is used to connect the same size low pressure tubing FEP ,PFA or PTFE on both ends, in the high pressures zones of HPLC systems. Due to its interior design, you can use this with 1/8" or 1/16th OD Tubing. The tubing ends will butt up against each other forming a zero dead volume connection. Nylon provides high strength and stiffness allowing for good connections when used with proper tubing connectors and all low pressure tubing grades.
Chemglass Life Sciences 18/9 Ball Joint, 13.0mm OD Tube, Clamp Size = 18
18/9 Ball Joint, 13.0mm OD Tube, Clamp Size = 18. Made to ASTM Specifications E677. See CG-145-B and CG-150 for clamps.
AVANTOR MASTERFLEX (VWR LLC) CPC (Colder) MPX17839 Quick-Disconnect Body, PS, 1/2"" ID; 5/Pk
All-plastic quick-disconnect couplings require a standard fitting body and standard insert or large fitting body and large insert (order separately). Simply press the thumb latch to disconnect fitting halves. Available in polycarbonate (PC), Acetal, and polysulfone (PSF).
AVANTOR MASTERFLEX (VWR LLC) CPC (Colder) HFCD16612 Valved Bulkhead panel mount hose barb, PP, 3/8"" flow size, 3/8"" ID
High-flow quick-disconnect couplings consists of a body and an insert (order fitting halves separately). Plug insert into coupling body to connect¿fitting halves lock into place immediately. To disconnect fitting halves, simply press the button on the coupling body. Valved models have a spring-operated 316 SS valve that seals the flow path when fitting halves are disengaged. All fitting bodies have 316 SS latch springs and EPDM seals.
AVANTOR MASTERFLEX (VWR LLC) CPC (Colder) HFCD22812 Quick-disconnect fittings, Valved hose barbs inserts, PP Body, 1/2"
High-flow quick-disconnect couplings consists of a body and an insert (order fitting halves separately). Plug insert into coupling body to connect¿fitting halves lock into place immediately. To disconnect fitting halves, simply press the button on the coupling body. Valved models have a spring-operated 316 SS valve that seals the flow path when fitting halves are disengaged. All fitting bodies have 316 SS latch springs and EPDM seals.
New Jersey Fluid Systems LLC SS MALE CONNECTOR 1/8 OD X 3.8
NC3793870 SS MALE CONNECTOR 1/8 OD X 3.8
AVANTOR MASTERFLEX (VWR LLC) Masterflex Fitting, Nylon, Straight, Hose Barb Union, 5/8"" ID; 10/PK
These economical straight barbed fittings easily connect fluid paths without the use of tools. Just slip your flexible tubing or hose onto the barb to create a secure seal.