Freeze Drying Chambers and Equipment
TA Instruments Ver 1 HA Aluminum Double Gap Concentric Cylinder Cup, Inner Radius 20 mm, Outer Radius 22.38 mm, Use with Upper Double Wall Rotor, Sample Volume 6.48 mL, Cup Insert Stainless Steel, for HR X0, DHR and AR-Series Peltier Jacket
Waters TA Instruments Ver 1 HA Aluminum Double Gap Concentric Cylinder Cup is for use with HR X0, DHR, and AR-Series Peltier Jacket. It is designed to be used with the upper double wall rotor. Cup inner radius is 20.00 mm, outer radius is 22.38 mm. Sample volume with the double wall rotor is 6.48 mL. The cup insert is stainless steel.
Chemglass Life Sciences 24 Position Pressure Manifold
24 Position Pressure Manifold.Note: Manifolds are supplied complete with the corresponding rubber gasket and the required amount of TFE needles. Replacement needles and gaskets are also available separately.
Mitegen Passive Drying and Storage Rack for 4L LN2 Dewars
Keep your lab organized and your 4L liquid nitrogen (LN2) dewars secure with the convenient Passive Drying and Storage Rack. This compact and stable stand provides a home for your dewars after cleaning procedures. This rack is the perfect companion to the Active 4L Dewar Drying Rack SKU M-CEM-NS-ADR-LD4-1, which uses heated, filtered air to completely dry the inside of your dewar in just 35 minutes. By pairing the two products, you can create a streamlined and efficient workflow for your lab's cryogenic storage. The rack offers an easy way to store your 4L dewars, ensuring they are always ready for use.
Bellco Glass, Inc. Low Profile 3-Port Stainless Steel Assembly , 6L
Stainless steel 3-port assembly for media bottles, 6l low profile. Welded, 316l stainless steel construction, 1/4" inch od tubing. MADE IN THE USAElectropolished finish, continuous seal weldThree port model features siphon, fill and vent tubes45mm polypropylene screw cap and silicone gasket includedCap slug: 45mmTube specifications: 1/4" OD X 5/32" ID, SIPHON (LONG TUBE): 10 13/32" LONG BELOW CAP SLUG, FILL TUBE: 3" LONG BELOW CAP SLUG, VENT TUBE: 1" LONG BELOW CAP SLUG.
Bellco Glass, Inc. Low Profile 3-Port Sparger W/Frit,6L For Vertical Side Arm Vessels
316-l stainless steel ra32 or better finish10 micron porosity stainless steel frit for low profile vertical side arm vessels. MADE IN THE USA. Frit is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasketTriple tube configuration With Vent, Fill/Sample And Sparge.
Bellco Glass, Inc. Low Profile 2-Port Stainless Steel Assembly ,6L
SST Low Profile Impeller Assembly For 6000mL Low Profile Vessels. Requires Over Head Drive & cap assembly. MADE IN THE USAMaterial: SST 316lConsist of: dust shield, shaft, paddle, locking ring, washer, cotter pinFour (4) SST set screws: 8-32 x 1/4"Dimensions: 9 1/2" to 12 1/2" oalPaddle size: 3" tall x 5 1/4" wideFully assembled
Ace Glass, Inc. Flask, 6L, evaporation, 295mm height, large flange
Flask, 6L, evaporation, 295mm height, large flange
Norell Inc 5mm, 500MHz 7" VALVED MEDIUM WALL NMR TUBE FOR INTERMEDIATE PRESSURE 1 Tube per pack
These pressure tubes facilitate experiments requiring conditions such as pressurized inert atmosphere blanketing, addition of reactive gaseous reagents under pressure, containment of low boiling point solvents or samples at elevated temperatures, and so on.We recommend that the maximum operating pressure should be limited to 600 kPa (6 bar, 87 psi) when using a thin wall pressure tube, up to 1200 kPa (12 bar, 175 psi) if using a heavy wall pressure tube. (Please see accompanying table for complete details).
Genesee Scientific Corporation 8-PORT MANIFOLDS
CLP supplies an 8-port manifold which has a friction slip fit on to the 50ml combi-syringe. The tips on the manifold follow the standard 9mm center microplate spacing. With aqueous solutions this tip will provide equal dispensing across all 8 tips to within 1.7% of the dispensed volume. Because of accuracy concerns across larger diameters, CLP does not supply a twelve-port manifold. Made of 100% virgin polypropylene