Conductivity Electrodes
OHAUS™ Starter Water Analysis Meter Replacement Electrodes
Replacement electrodes for Starter portable and benchtop meters.
Cole-Parmer Oakton Conductivity/Temp Probe, for 6 and 6+ Series Meters; K=1.0
Replacement Conductivity/Temp probe, K=1.0 for Oakton 6 and 6+ series meters
Hach Company Radiometer Analytical CDC511T Conductivity Cell with Temperature Sensor (4-pole Pt sensor, k = 1.0 cm-1)
The Radiometer CDC511T is a 4-pole conductivity cell with non-platinized, platinum sensor (k = 1.0 cm-1), integrated temperature sensor and TPX body. The CDC511T sensor's 4 platinum ring design ensures results in general aqueous and non-aqueous media over several decades of conductivity with a single cell, using just one calibration. The CDC511T can be used with a flow-through cell for pure water measurements and meets requirements of USP 24-NF19. It has a fixed cable with MAB6 plug for use with Radiometer Analytical CDM210/230/92 conductivity meters.
Cole-Parmer Oakton SS Cell Conductivity Probe, Epoxy, K=1.0; 2.5 ft Cable
Ultem Body, SS Electrodes Conductivity Cell for OAKTON Conductivity and TDS Meters, K=1.0, 2.5' Cable
Pendotech 1/4 Inch Hose Barb Single Use Conductivity Sensor
Single Use Conductivity Sensor, non-sterile, polysulfone 1/4 inch hose barb
Cole-Parmer Conductivity Cell, K=1.0, 10 KOhm ATC, Glass; Type F
These 10-foot cables with stripped ends are economical replacements for a variety of controllers. There are flow-through, in-line, swage, and dip styles available.
Hach Company Radiometer Analytical CDC749 Conductivity Cell for Microsamples - 2-pole platinized Pt probe, k = 1.7 cm⁻¹, 4 mm lower diameter, glass body, fixed cable with MAB6-style plug; compatible with MeterLab/CDM series
The Radiometer Analytical CDC749 is a compact 2-pole conductivity cell designed for precise conductivity measurement of microsamples and small-volume samples in test tubes. It features a platinized platinum electrode, a cell constant of 1.7 cm⁻¹, and a small lower diameter for limited sample volumes. The glass body and robust construction provide chemical compatibility and measurement stability.
- Designed for microsamples and test-tube measurements.
- Platinized platinum 2-pole electrode for stable conductivity readings.
- Cell constant k = 1.7 cm⁻¹ for accurate low-volume measurements.
- 4 mm lower diameter to fit small sample volumes.
- Glass body for chemical compatibility and dimensional stability.
- Fixed cable with a multi-pin plug for direct connection to compatible meters.
- Supplied with a certificate of conformity and a 12-month warranty.
Grainger Graphite Conductivity Sensor 0.48 Dia.
The Grainger Graphite Conductivity Sensor is a sensor used to measure the electrical conductivity in liquids. It has a 316 stainless steel body, graphite electrodes, and a 3/4" NPT process connection. The sensor has a max pressure rating of 3000 psi at 100°F and a max temperature rating of 750°F. It has a cell constant of 0.1 cm−1. The sensor can be used for applications such as boiler water level control, cooling tower conductivity control, reverse osmosis system monitoring, and water purification monitoring. It requires a compatible conductivity transmitter to provide power and convert the signal.
Pendotech 1/2 Inch Hose Barb Single Use Conductivity Sensor
Single Use Conductivity Sensor, non-sterile, polysulfone 1/2 inch hose barb
TA Instruments Stainless Steel, Composite HB, 20 mm, NST, Upper Plate with Composite Heat Break, for Use with Lower Peltier Plate, Smart Swap 2 Geometry, HR x0 Instruments Only
Waters TA Instruments HR X0, Stainless Steel, Composite HB, 20 mm, NST is an upper plate with composite heat break for use with the lower Peltier plate. It has Smart Swap 2 geometry and is for use with HR X0 instruments only.