Electron Microscope Accessories
Electron Microscopy Sciences Calibration Specimen 300-2D, SEM Pin
SPM calibration specimens are produced by holographic fabrication that assures high accuracy and precision. The standards provide easier testing of your SPM, improved accuracy of critical dimension measurements and accuracy of 0.5% (1 std. dev.). The pattern height of greater than 100nm provides excellent image contrast. There is uniform coverage of entire chip which allows for imaging anywhere on the chip. Array of Posts. Pitch 297. Al bumps on Si. Use contact or TappingMode.
Mount: SEM Pin
Electron Microscopy Sciences Formvar Support Film 10 nm thick on Hexagonal 200 mesh Nickel Grid
A thin film of pure formvar resin coats the shiny side of a hexagonal grid. Coated grids are optically checked and batch tested in the electron microscope. Packed in grid storage box. Coating is 10 nm thick.
Grid: Nickel
Electron Microscopy Sciences EMS Swiss Line Wafer Handling Tweezer Style NW, 130 mm
130 mm long. B = 16 mm, C = 6 mm, M = 11 mm, N = 2 mm, R = 52 mm, S = 42 mm.
OAL: 130 mm
Tip width: B: 16 mm
Gap: N:2 mm
Tip lip: C: 6 mm
Dimensions: M: 11 mm, R: 52 mm, S: 42 mm
Electron Microscopy Sciences Formvar/Carbon Support Film 10 nm/1 nm thick on London Finder LF135 Nickel Grid
A formvar coated grid, stabilized with evaporated carbon film. This type of coating is excellent for specimen support, especially for ultra thin sections. Coated grids are optically checked followed by batch testing in the electron microscope. Packed in grid storage box. NOTE: All film is laid on the shiny side of the grid. Formvar is approximately 10 nm thick with 1 nm of carbon.
Grid: Nickel
Electron Microscopy Sciences Formvar/Carbon Film 10 nm/1 nm thick on Thin Bar Hexagonal 400 mesh Copper Grid
A formvar coated grid, stabilized with evaporated carbon film. This type of coating is excellent for specimen support, especially for ultra thin sections. Coated grids are optically checked followed by batch testing in the electron microscope. Packed in grid storage box. NOTE: All film is laid on the shiny side of the grid. Formvar is approximately 10 nm thick with 1 nm of carbon.
Grid: Copper
Electron Microscopy Sciences Formvar Support Film 5-6 nm thick on Thin Bar Hexagonal 200 mesh Copper Grid
A thin film of pure formvar resin coats the shiny side of a thin bar hexagonal grid. Coated grids are optically checked and batch tested in the electron microscope. Packed in grid storage box. Standard coating is 5 to 6 nm thick.
Grid: Copper
Electron Microscopy Sciences Formvar Support Film 5-6 nm thick on Thin Bar Hexagonal 300 mesh Copper Grid
A thin film of pure formvar resin coats the shiny side of a thin bar hexagonal grid. Coated grids are optically checked and batch tested in the electron microscope. Packed in grid storage box. Standard coating is 5 to 6 nm thick.
Grid: Copper
Electron Microscopy Sciences Formvar Support Film 5-6 nm thick on Thin Bar Hexagonal 600 mesh Copper Grid
A thin film of pure formvar resin coats the shiny side of a thin bar hexagonal grid. Coated grids are optically checked and batch tested in the electron microscope. Packed in grid storage box. Standard coating is 5 to 6 nm thick.
Grid: Copper
Electron Microscopy Sciences Metallurgical Mount Holder 1.5" and 40 mm, 3.2 mm x 8mm Pin
This set screw vice which is made from machined aluminum with stainless steel allen set screws has an open slot that is 10 mm (.394") wide x 5 mm (.197") deep. It measures 25 mm (1”) dia. x 17.5 mm (0.69”) high.
Type: 3.2 mm x 8 mm Pin
Electron Microscopy Sciences Hitachi M4 SEM Cylinder Mount 2" surface, 1/4" height, Aluminum
Hitachi M4 Thread SEM mounts made from lathe finished ultra-pure aluminum.
Head: 2"
Height: 1/4"
Electron Microscopy Sciences SEM Cylinder Mount 45° Angle 1" Surface, Aluminum
Scanning electron microscope specimen mount with 45 degree angle. Made from lathe finished ultra-pure aluminum.
Head: 1"
Height: 13/16"
Electron Microscopy Sciences EMS Molybdenum Aperture with 50 µm hole, 6 mm O.D., 0.24 mm thick
O.D.: 6 mm
Thickness: 0.24 mm
Electron Microscopy Sciences Formvar Support Film 5-6 nm thick on Single 1500 µm hole Copper Grid
A thin film of pure formvar resin coats the shiny side of a single hole grid. Coated grids are optically checked and batch tested in the electron microscope. Packed in grid storage box. Standard coating is 5 to 6 nm thick.
Grid: Copper