General Spectrometer Accessories
Electron Microscopy Sciences Omniprobe Short-Cut™ Coupons Backside Thinning, Copper, 26.5° Angle
TEM sample grid coupon designed specially for use in the Short-Cut™ tool. The center portion is a standard 3 mm grid into which the sample loaded needle is swaged and cut.
Material: Copper
Angle: 26.5°
Glass Expansion Quartz Outer Tube
Quartz Outer Tube. Compatible with Thermo (TJA) Iris, Tracescan, Trace, Advantage, Intrepid Axial ICP-OES, ABC Fully Demountable Torch (30-808-0704). The fully demountable torch, provides a robust and high-performing alternative to both single-piece and semi-demountable quartz torches, ensuring greater robustness and a lower cost of ownership. With the fully demountable torch design, the analyst most often replaces only the outer tube, rather than replacing the entire torch or a quartz torch body.When not in use, clean as per recommended guidelines, and store in original box.Glass Expansion is ISO 9001:2015 certified by AB Certification, No. AU4501-9001
Revvity Health Sciences Inc OptiPlate 96-well 1/2 Area, white, case of 50
OptiPlate 96-well 1/2 Area, white, case of 50
Glass Expansion IsoMist XR Kit for Spectro Blue/Green SOP ICP-OES
IsoMist XR Kit for Spectro Blue/Green SOP. Compatible with Spectro Blue/Green SOP ICP-OES. This IsoMist XR is programmable and temperature-controlled, with a glass cyclonic spray chamber now featuring an improved thermodynamic design that provides an extended temperature range of -25°C to +80°C. The temperature is settable in 1°C increments and can maintain accuracy of + or – 0.1°C. Proven performance results are, improved long-term stability and precision, no dilution for volatile organic solvents, reduced oxide interferences (ICP-MS), enhanced sensitivity and accuracy, lower detection limits, faster washout, and reduced hazardous waste/disposal fees.Replacement parts include 21-809-3185, GAZ-04-90, and 501907304.The IsoMist XR comes standard with a borosilicate glass spray chamber. Optional quartz or PFA HF-resistant spray chambers can be ordered separately.Glass Expansion is ISO 9001:2015 certified by AB Certification, No. AU4501-9001
Glass Expansion Shimadzu ICP-MS 2030, Silver Coil. To ensure correct installation, the Installation Kit 70-900-6000T is required. This is not included and must be ordered separately. It is re-useable so only needs to be ordered once.
RF Coil Silver for Shimadzu 2030 ICP-MS. Compatible with Shimadzu 2030 ICP-MS. The RF coil is susceptible to corrosion in the torch box, which eventually lowers the conductivity of the coil. The greater the corrosion, the larger amount of energy is needed to produce a plasma of the same power. Coils in a corroded condition, increases the stress applied to other components in the RF generating system, and can shorten the lifetime of your torch. Copper is used as the base material of most commercially available coils but different plating materials are available. Silver has the best conductance & gold the best corrosion resistance. For Copper 501907336, Goild 501907337.To install your coil and ensure proper alignment, we highly recommend our re-useable RF Coil Installation Tool Kit (501907339).Glass Expansion is ISO 9001:2015 certified by AB Certification, No. AU4501-9001
Glass Expansion Nickel Plated Platinum Sampler Cone for Agilent 7700/7800/7900/8800/8900 (G32880-67142)
Platinum Sampler Cone with Nickel Plated Base (G3280-67142) ¿ For Agilent 7700/7800/7850/7900/8800/8900 ICP-MS. For use with aggressive acid matrices (e.g., HCl, HF, HClO4) and high matrix samples. Use with platinum skimmer cone and brass skimmer base. Use 10x Magnifier Inspection Tool with Built-In LED Illumination (NC2042261) to inspect cone orifice condition. When not in use, keep cones stored in original packaging for protection.For routine samples with x-lens, use P/N 501907575. For high TDS samples causing rapid cone deposition, use Pt Sampler with Ni Base, P/N 501907585 or 501907583. For lowest Ni background & laser ablation applications, use Al Sampler, see AT7701-Al.Glass Expansion is ISO 9001:2015 certified by AB Certification, No. AU4501-9001
Glass Expansion MicroMist DC Nebulizer 0.2mL/min, Includes NFT-050 UniFit Connector with 0.50mm ID x 1.3mm OD x 700mm long tubing (1 piece) and 70-803-0969 Gas Fitting with Ratchet Nebulizer connector
MicroMist DC Nebulizer 0.2 mL/min, includes UniFit Connector with 0.50mm ID x 1.3mm OD x 700mm long tubing (1 pc.) and DC Gas Fitting Type 11 with ratchet connector (1 pc.). Compatible with Analytik Jena ICP-MS and Leeman.Optimum nebulizer gas flow rate is 1.0L/min and sample flow rate is 0.2mL/min. Recommended not to exceed optimum 0.2mL/min sample flow rate; however, lower gas and sample flow rates are OK. The backpressure should read ~40 psi at 1.0L/min gas flow rate. Can tolerate up to 15% TDS. MicroMist is the standard configuration for many ICP manufacturers due to its excellent sensitivity and precision at low flow rates. Replacement parts include P/Ns NC1625341 and 502703076.Recommend maintenance tools are Fluka RBS25 (P/N NC9000117) and Eluo Nebulizer Cleaning Tool (P/N NC9462559). When not in use, best to store in the provided hard plastic case.Glass Expansion is ISO 9001:2015 certified by AB Certification, No. AU4501-9001
Glass Expansion VeeSpray Ceramic DC Nebulizer, Includes STT-16-75 Sample Tubing 0.75mm ID x 1/16 OD (750mm length), 70-803-1350 Ratchet Connector and 70-803-0772 Ferrule for VeeSpray Nebulizer (1 of each), and 70-803-1311 Gas Fitting with Ratchet Nebulizer connector
VeeSpray DC Nebulizer, includes UniFit Connector with 0.75mm ID x 1.6mm OD x 750mm long tubing (1 pc) & DC Gas Fitting Type 41 with ratchet connector (1 pc). Compatible with Analytik Jena ICP-MS and Leeman.Optimum nebulizer gas flow rate is 1.0L/min & sample flow rate best between 1.5 - 2.5mL/min, must be pumped. Backpressure should read ~40 psi at 1.0L/min gas flow rate. VeeSpray is a V-groove design made from ceramic, ideal for greatest resistance to large particulates, high TDS & HF. Tolerates up to 30% TDS & 300um particulates, providing a robust, virtually unblockable nebulizer. Replacement parts include STT-16-75, 70-803-1350, 70-803-0780, 70-803-1955.Recommend nebulizer cleaning solution is Fluka RBS25 (P/N NC9000117). When nebulizer is not in use, best to store in the provided hard plastic case.Glass Expansion is ISO 9001:2015 certified by AB Certification, No. AU4501-9001
Glass Expansion Conikal U-Series Nebulizer 2mL/min (G8010-60270, N0777487, N0777707, 3203393, 842312051431)
Conikal U-Series Nebulizer 2.0 mL/min, includes UniFit Connector with 0.75mm ID x 1.6mm OD x 700mm long tubing (1 pc.) and EzyLok Connector (1 pc.).Optimum nebulizer gas flow rate is 0.7L/min and sample flow rate is 2.0mL/min. Recommended not to exceed optimum 2.0mL/min sample flow rate; however, lower gas and sample flow rates are OK. The backpressure should read approximately 40psi at 0.7L/min gas flow rate. The Conikal nebulizer is a high-performance, general use glass nebulizer, that tolerates up to 5% TDS and 75um particulates. Replacement parts include P/Ns NFT-16-75 and 502702994.Recommend nebulizer maintenance tools, Fluka RBS25 (P/N NC9000117) and Eluo Nebulizer Cleaning Tool (P/N NC9462559). When nebulizer is not in use, best to store in the provided hard plastic case.Consider upgrading to our new Direct Connect (DC) Conikal to take advantage of the cost-effective design improvements.Glass Expansion is ISO 9001:2015 certified by AB Certification, No. AU4501-9001
Glass Expansion Platinum Skimmer Cone with Nickel Base for x-lens for Agilent 7900/8900 ICP-MS (G3280-67202)
Platinum Skimmer Cone with Nickel Base for x-lens (G3280-67202) ¿ For Agilent 7900/8900 ICP-MS. Recommended for organic samples. More durable, longer-lasting, & because it runs hotter it requires less frequent cleaning. Use 10x Magnifier Inspection Tool with Built-In LED Illumination (NC2042261) to inspect cone orifice condition. Use Skimmer ConeGuard (70-803-1004) to protect cone threads during cleaning. When not in use, keep cones stored in original packaging for protection.For routine applications, use standard Nickel Skimmer for x-lens, see P/N 501907593.For corrosive analysis, use Platinum Skimmer with Cu Base for x-lens, P/N 501907596, which must be mounted on brass adaptor skimmer base, see P/N AT7905X-BR. For lowest nickel background and laser ablation applications, use Aluminum Skimmer for x-lens, see P/N AT7902X-Al.Glass Expansion is ISO 9001:2015 certified by AB Certification, No. AU4501-9001
Perkin Elmer US LLC Argon/Nitrogen Regulator, Color-coded hose with 1/4 in. Swagelok fitting included
Color-coded hose with 1/4 in. Swagelok fitting included.
Perkin Elmer US LLC Drain Tubing for S10/AS-93plus
The tubing has a 6.4 mm inner diameter, a 1.6 mm wall thickness and is clear in color. Note that the tubing is part of the Rinsing Kit B3140236.