Special Purpose Racks
Chemglass Life Sciences Support Tubes, Stainless Steel, 1/2in OD X 12in Length
Support Tubes, Stainless Steel, 1/2in OD X 12in Length. These support tubes are made of brilliant polished 304 stainless steel. They have good surface hardness and do not score from clamp binding screws. Tubes are 1/2" (13mm) in diameter, and are hollow, reducing weight to 1/2 of solid stainless steel rods while maintaining all the advantages of the stainless steel. The walls are 1/16" (1.6mm) thick, strong, and do not sag. The ends of each tube are capped with polyethylene tight fitting end-caps.
Research Products International Corp Poxygrid Centrifuge Tube Rack, 6 Places
Durable epoxy coated steel wire racks are designed to hold centrifuge tubes. Heat-cured epoxy coating is unaffected by organic solvents, salts, weak acids and weak alkalis. Racks feature dual tiers and rail channels for maximum tube stability.
Electron Microscopy Sciences Large Coverglass Staining Rack, Stainless Steel
Made from polished stainless steel, this staining rack securely holds thirty 22 or 24 mm cover glass. Welded stainless steel. Spring-type detachable handle. 4" (10.2cm) long.
Electron Microscopy Sciences Coverglass Staining Rack, Stainless Steel
Coverglass staining rack made from polished stainless steel. Specially designed to be used with coplin jars. Holds five of 22 x 24 mm coverglass. Comes with a handle 5" (127 mm) long.
Research Products International Corp Flipper 4-Way Tube Racks, Assorted Colors (Blue, Green, Orange, Pink, Yellow), 5 per Case
Flipper 4-Way Tube Racks are designed to hold a variety of tube sizes and styles. Racks can be rotated to any of four positions to accommodate: 4-50 ml conical tubes 32-12x75 or 1.5 ml tubes 12-15 ml conical tubes 32-0.5 ml micro-tubes Autoclavable racks are constructed of durable polypropylene and can be used in water baths and freezers.
Electron Microscopy Sciences Adjustable Coverglass Rack 1 each
This polypropylene rack accommodates a cover-glass in all sizes by simply adjusting the holder to fit the cover glass and then securing it by tightening the reset screws with the hex key. The holder is made from non ferrous material, so it is microwaveable.
The rack accommodates 10 cover glasses, round, square or rectangular, adjusting from 5 mm to 60 mm. Removable handle. Rack comes with two set of holding rods. One set accommodate cover glasses from 5 to 25 mm, and the other set for cover glasses from 5 mm to 60 mm. Rack measures 1-1/2" W x 1-1/2" H (48 x48 mm).
Electron Microscopy Sciences Rota-Rack for Microtubes
Connect up to 4 interlocking racks and rotate each of the four modules independently. Use several sizes of test tubes, culture tubes, centrifuge tubes, or microcentrifuge tubes at the same time. Click each module into place, load with tubes, and carry! Rack maintains its orientation until you twist it again. Comes fully assembled. Autoclavable. Holds 6 15 ml, 9 1.5/2.0 ml, 12 0.5/0.6 ml , or 32 0.2 ml PCR* tubes or 4 8-tube strips.
Research Products International Corp Poxygrid Centrifuge Tube Rack, 16 Places
Durable epoxy coated steel wire racks are designed to hold centrifuge tubes. Heat-cured epoxy coating is unaffected by organic solvents, salts, weak acids and weak alkalis. Racks feature dual tiers and rail channels for maximum tube stability.
TrippNT Dissolution Vessel Holder
TrippNT's Dissolution Vessel Holder can hold 6 dissolution vessels with widths up to 4 3/8". The corners are open to allow water to flow through and allow carrier to drain. On either side of the holder there are handles cut into the material for easy transportation. This holder is constructed out of white PVC and ships fully assembled.
•White Rectangular Design with (6) 4 3/8" Diameter Openings
•Corners are Open to Allow Water to Flow Through and Allow Carrier to Drain
•Constructed from White PVC
•Holds Dissolution Vessels so they can be Easily Transported
•100% Total Replacement Lifetime Guarantee/Made in USA
Analytical Sales & Services Blue Stackable 96 Position PCR Racks
Blue Pc Rack with Clear Lid, Pack/20.
Electron Microscopy Sciences Winlab Slide Rack LSM-30, 30 Slide Capacity
WINLAB Racks are made from Poly-ceramic that maintains its structural integrity to 200 degree C in any solvent while being microwaved. Designed for histology and cytology staining and coverslipping. They last a lot longer than any other materials and save time and money. Held rigid by carrier and swivels. Fits Leica, VBS, Bayer, Sakura, Medite coverstaining machines and Sakura tape coverslipper
Capacity: 30 slides
Electron Microscopy Sciences Vertical 48 Slide Rack only
A stainless steel rack with a fixed handle for use with large slides. Rack is grooved to take 76mm microscope slides up to 50mm wide horizontally. Accommodates up to 55 slides.
Electron Microscopy Sciences Winlab Slide Rack Wire Handles for 20 Slide Rack
Steel wire is bent to form a handle, use these handles for manual staining and the Medite stainer, Model W3-6 fits all WINLAB 20-Slide Racks.
Capacity: 20 slides