TLC Developing Tanks
Camag Scientific CAMAG Flat bottom chamber for 20x20cm plates, with stainless steel lid`
CAMAG Flat bottom chamber for 20x20cm plates, with stainless steel lid`
Chemglass Life Sciences TLC Bottle only, Cylindrical, 34/15 Joint Size, Fits Plate 1in X 4
Replacement TLC bottle for the CG1181 series of TLC developing chambers. Bottle only, Cylindrical, 34/15 Joint Size, Fits Plate 1in X 4
Camag Scientific Tlc Plate Heater 3, 115 V, For Tlc/Hptlc Plates Up To 20 X 20 Cm, Temperature Range 25 - 200 ºc
The Tlc Plate Heater 3 Is A Device For Heating Tlc/Hptlc Plates, Permitting Optimal Heating During The Derivatization Reaction. It Features A Ceran Heating Surface Which Is Resistant To All Common Reagents And Is Easily Cleaned. The 20 X 20 Cm Heating Surface Has A Grid To Facilitate Correct Positioning Of The Plate. Programmed And Actual Temperature Are Digitally Displayed. The Temperature Is Selectable Between 25 And 200 °C. The Plate Heater Is Protected From Overheating.
Camag Scientific Horizontal Developing Chamber For 10 X 10 Cm Plates
In The Horizontal Developing Chambers, Hptlc Plates Can Be Developed From Both Opposing Sides Towards The Middle. This Permits The Number Of Samples To Be Doubled As Compared With Development In A Tank, Provided The Separation Distance Of 45 Mm, I.E. 50 Mm Minus 5 Mm Distance From The Edge, Is Sufficient. This Chamber Type Is Often Used For Screening Purposes. The Obtained Chromatograms Differ From Those Obtained With The Same Mobile Phase System Developed In Vertical Chambers. This Chamber Is Suitable For Plates Up To 10 X 10 Cm In Size.
Camag Scientific Dip Tank 20 X 10 Cm
Dip Tank (Sintered Sheet Glass) For Plates 20 X 10 Cm, With Lid, For Use With The Chromatogram Immersion Device 3
Chemglass Life Sciences TLC Bottle only, Cylindrical, 34/15 Joint Size, Fits Plate 1in X 3
Replacement TLC bottle for the CG1181 series of TLC developing chambers. Bottle only, Cylindrical, 34/15 Joint Size, Fits Plate 1in X 3.
Chemglass Life Sciences TLC Tank Rack, Aluminum, PTFE Coated
PTFE coated aluminum rack to fit either CG-1183 or CG-1184 TLC developing tank. Rack will hold six 20cm x 20cm x 1/8in or twelve 20cm x 20cm x 1/16in plates.
Chemglass Life Sciences TLC Stopper only, 34/15 Joint Size
Replacement TLC stopper for the CG1181 series of TLC developing chambers. Stopper only, 34/15 Joint Size.
Electron Microscopy Sciences Film Developing Tank 5x7", 10.8 x 19.7 x 18.4 cm
Hard plastic tanks and floating lids.
I.D.: 10.8 x 19.7 x 18.4 cm
Use: EMS film racks
Miles Scientific DEV CHAMBER FOR 20X20 PLATES
Glass Rectangular Developing Chamber for 20x20cm plates, Sturdy, molded-glass block of clear glass with flat surface walls, ground lip of uniform flatness, Beveled inside and outside to remove any sharp edges.Comes with flat, clear glass li
Miles Scientific Latch-Lid Developing Chamber for 20x20 cm TLC Plates
Analtech's glass TLC developing chambers provide optimum developing conditions for a variety of TLC plate sizes and shapes. Precision ground surfaces provide tight seals between tanks and glass covers and permit complete saturation of chambers with solvent vapor for uniform development of chromatograms. Each chamber is shipped with the appropriate lid. Inside Dimensions: 25 cm H x 28 cm W x 7.5 cm D. For use with: 20 x 20 cm TLC plates or smaller.
Alkali Scientific CellPro™ Magnetic Bead Separation Rack, Reversible, with Magnet Sleeve and Microtube Height Adjustment Ring
CellPro™ reversible magnetic separation rack is ideal for low throughput bead-based nucleic acid purification. Double-sided magnets combined with an innovative flip-design allow for bead separation in 8 x 1.5/2.0mL microtubes, or 16 x 0.2mL PCR tubes, all while maintaining an exceptionally compact footprint (3.75 × 1.75 × 1.5in.). The ultra-strong magnets feature a Pull Strength of 5000g and Field Strength of more than 5000 gauss for fast separation. Tube wells are angled on a 10° pitch for optimal tube contact with magnets, and microtube wells are equipped with an adapter ring for precision control over the height of the tube exposed to the magnetic field. The magnets are housed in a removable casing that enables quick resuspension without removing tubes from the rack. • Flip-Over Design for Microtubes or PCR Tubes• Powerful Magnets for Quick, Efficient Separation• Removable Magnet Sleeve for Resuspension• Adapter Rings for Variable Tube Height
SKC Inc PHENOL DEVELOPING SOLU. 16OZ
DOES NOT ship to Alaska, Arizona, California, Colorado, Hawaii, Idaho, Nevada, Oregon, Utah, Washington. Wyoming”
Electron Microscopy Sciences EMS Film Racks for 3 1/4 x4" Film
Fabricated acrylic racks that are designed to fit with Kodak developing tanks. Sheet film is firmly held in the slots in the side rails while solution is freely circulating inside the tank. Measurements 3.5 x 6-7/8 x 6"H. Holds 18 sheets of film 3 1/4 x 4"