Evaporator Accessories
Electron Microscopy Sciences Palladium/Gold 40, 0.20 mm, Purity 99.90% 10 FT
High purity, vacuum grade. These metal wires are suitable for scanning and electron microscopy techniques.
Size: 0.20 mm
Purity: 99.90%
Electron Microscopy Sciences Molybdenum Wire, 0.20 mm, Purity 99.95% 50 FT
High purity, vacuum grade. These metal wires are suitable for scanning and electron microscopy techniques.
Size: 0.20 mm
Purity: 99.95%
Chemglass Life Sciences Vapor Tube, Compatible with Buchi Rotary Evaporators, 24/40, 288mm OAL, Decaled "R111/140", Length A is 160mm
Vapor Tube, Compatible with Buchi Rotary Evaporators, 24/40, 288mm OAL, Decaled "R111/140", Length A is 160mm. Replacement Vapor tubes compatible with Buchi rotary evaporators. Thread is made for use with standard Combi-Clip.
Glas Col LLC Evaporator Accessory
Aluminum insert block, 24 position for up to 12mm vials. Use with small evpaorator system 109A YH-1.
Electron Microscopy Sciences Tip Check
The Tipcheck is used for examining the shaft of the tip probe and for determining tip breakage. In AFM, an independent means of assessing the influence of the probe tip on the image is desirable since a broken or misshapen probe tip results in inaccurate rendering of samples. If the tip damage goes undetected, the true topographical nature of your samples may inadvertently go unnoticed.
A simple, convenient means to prescreen all of one's AFM tips is TipCheck. TipCheck exploits reverse imaging to provide a fast and simple way to assess new and used tips without the need for SEM inspection and permits qualitative comparisons between tips. The microstructure of the TipCheck film is ideal for the detection of tip morphology in the vicinity of the tip apex. The AFM images shown here were obtained by imaging a TipCheck surface with (left) a broken tip and (right) a reasonably good tip.
Ace Glass, Inc. Trap, bump, 500mL, 24/40 top, 24/40 bottom
500mL bump trap for use between the rotary evaporators steam tube and evaporator flask, preventing fluid from being drawn into the condenser. Trap has 24/40 top and bottom joints.
Sigma Aldrich Fine Chemicals Biosciences CaptoTM Core 700 Cytiva 17
Novel core bead technology and multimodal octylamine ligand give Capto Core 700 dual functionality. This chromatography resin has both size exclusion and binding properties.
Chemglass Life Sciences 11 Well Evaporator/Concentrator Manifold, Replaceable Needles
11 Well Evaporator/Concentrator Manifold, Replaceable Needles. Manifold is a low cost solution for the concentration of product in 96, 48 or 24 well blocks. Delivers equal amounts of gas to each well to gently speed solvent evaporation. Needles are constructed of stainless steel. The 11 well units have removable/replaceable needles. Manifold is constructed of polypropylene and the base is coated aluminum. Equipped with an adjustable flow meter for controlling gas flow into the manifold. Inlet is a 1/8” barbed fitting.Note: Blocks are not included and must be purchased separately.
Chemglass Life Sciences 12-Position Block for 25 x 100mm Round Bottom Tubes, Two Tier Design
12-Position Block for 25 x 100mm Round Bottom Tubes, Two Tier Design. Vial and tube holders for use in centrifugal vacuum evaporators. Blocks are designed to not only maximize evaporation but also to minimize the weight of the block, thereby increasing sample volumes. Constructed of aluminum, each block is black hard coated for resistance to organic solvents and laser etched with the vial/tube size.
Ace Glass, Inc. Valve, distribution head inlet assembly, complete with valve stem, bushings and O-rings, part 41348
Valve, distribution head inlet assembly, complete with valve stem, bushings and O-rings, part 41348
Chemglass Life Sciences 24 Well Evaporator/Concentrator Manifold, Replaceable Needles
24 Well Evaporator/Concentrator Manifold, Replaceable Needles. Manifold is a low cost solution for the concentration of product in 96, 48 or 24 well blocks. Delivers equal amounts of gas to each well to gently speed solvent evaporation. Needles are constructed of stainless steel. The 24 well units have removable/replaceable needles. Manifold is constructed of polypropylene and the base is coated aluminum. Equipped with an adjustable flow meter for controlling gas flow into the manifold. Inlet is a 1/8” barbed fitting.Note: Blocks are not included and must be purchased separately.