Stirrer Accessories
Chemglass Life Sciences Agitator, PTFE, Four Blade, 5in Diameter, Fits 19mm Shaft Size, 60° Impeller Angle
Agitator, PTFE, Four Blade, 5in Diameter, Fits 19mm Shaft Size, 60¿ Impeller Angle. Agitators are made entirely of PTFE and glass filled PTFE and are for use with 19mm OD stirrer shaft CG-2097 and have 60¿ impeller angles. The 60¿ impellers are set up to stir downwards in a clockwise direction and upwards when rotated counter-clockwise. Agitator hub is open so that it can be positioned anywhere along the shaft. Locks onto shaft with a collet hub and nut and has a glass filled PTFE safety screw. PLEASE NOTE: ANGLED IMPELLARS DESIGNED TO STIR UPWARDS IN A CLOCKWISE DIRECTION ARE AVAILABLE. PLEASE CALL FOR PRICING.
Chemglass Life Sciences 10mm Chem-Vac Stirrer Bearing, PTFE, 29/42 Joint Size
10mm Chem-Vac Stirrer Bearing, PTFE, 29/42 Joint Size. Chem-Vac PTFE stirrer bearing provides a VACUUM TIGHT FLAKE-FREE SEAL. Two versions of the bearing are available, the standard series for 2L and smaller vessel capacities and the stabilizer series that incorporates a PEEK/PTFE stabilizing bushing that is molded to the lower portion of the inner joint. The stabilizer greatly reduces stirrer shaft whip on larger vessels. The bearing consists of a PTFE standard taper body, Glass filled polypropylene screw cap, PEEK Compression spring, PEEK/PTFE sleeve and a glass filled polypropylene loosening nut. The polymer blend sleeve provides a long lasting seal for use up to 500 RPM. Loosening nut above the standard taper inner joint allows easy and quick removal. PLEASE NOTE: PTFE STIRRER SHAFTS ARE NOT RECOMMENDED FOR USE WITH THIS BEARING.
Chemglass Life Sciences Agitator, PTFE, 10mm, Four Blade, 75mm Dia, Fits Shaft Size 10mm, 60° Impeller Angle
Agitator, PTFE, 10mm, Four Blade, 75mm Dia, Fits Shaft Size 10mm, 60¿ Impeller Angle. Agitators are made entirely of PTFE and glass filled PTFE and are for use with 10mm OD stirrer shaft CG-2075-B. Available in 45¿, 60¿ and 90¿ impeller angles. The 45¿ and 60¿ impellers are set up to stir downwards in a clockwise direction and upwards when rotated counter-clockwise. Agitator hub is open so that it can be positioned anywhere along the stirrer shaft and locks onto shaft with a glass filled TFE screw.
Chemglass Life Sciences Motor Adapter, 5/16" Male to 3/8" Female
Motor Adapter, 5/16" Male to 3/8" Female. Replacement part for CG204701 Flexible Drive Shaft.
Chemglass Life Sciences Stirring Shaft, 19mm, Polished, Glass Agitator, Three-Blade, 625mm OAL, for 3000mL Reactors, 105mm OD Agitator
Stirring Shaft, 19mm, Polished, Glass Agitator, Three-Blade, 625mm OAL, for 3000mL Reactors, 105mm OD Agitator. Shaft is precision ground and polished to fit our CG-2086 19mm PTFE bearings. Designed to be used with cylindrical type reactors. The curved glass blades are spaced 120° apart and angled upward.PLEASE NOTE: STIRRER SHAFTS ARE DESIGNED FOR COUNTER-CLOCKWISE ROTATION.ALSO NOTE: 19MM SHAFTS HAVE A REDUCED DIAMETER TOP SECTION THAT IS 1/2"OD, PLEASE KEEP THIS IN MIND WHEN SELECTING THE PROPER SIZE COUPLING.
Chemglass Life Sciences 10ft Extension Cord, Type "K" (Yellow), Standard to Mini Plug
10ft Extension Cord, Type "K" (Yellow), Standard to Mini Plug. Coiled extension cords to connect thermocouples to instrumentation such as temperature monitors, controllers and data loggers. Cords are 10ft long and made of 26-gauge multistrand wire with PVC insulation. All cords have a female standard (OST) with a choice of a male standard (OST) or mini (SMP) connection.
Chemglass Life Sciences 10mm Stirring Shaft, Chem-Stir, Polished, For Use With 300mL-500mL Flasks, 405mm OAL, Complete with PTFE Nut and Bolt
10mm Stirring Shaft, Chem-Stir, Polished, For Use With 300mL-500mL Flasks, 405mm OAL, Complete with PTFE Nut and Bolt. A 10mm OD precision ground and polished stirrer shaft with our patented** Chem-Stir blade attachment system. Shaft (C) has been manufactured with a ring at the lower end to permit attachment of the blade (B) with a PTFE nut (D) and bolt (A). Shaft is supplied complete with PTFE nut and bolt set. For use with PTFE bearings such as the CG-2077. Polished shaft will not cause abrasion to the sealing surfaces of the PTFE bearing, thereby allowing a vacuum tight seal. Uses the same PTFE nut and bolt blade attachment method as the CG-2074 ground shaft. PLEASE NOTE: STIRRER BLADES MUST BE PURCHASED SEPARATELY.THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF GLASS BEARING. FOR GROUND SHAFTS USED WITH GLASS BEARINGS SEE CG-2074.
Chemglass Life Sciences 10mm OD x 440mm Stirrer Shaft
10mm OD x 440mm Stirrer Shaft. Replacement part for CG206401 Semi-Micro Stirrer Assembly.
Chemglass Life Sciences Stirring Shaft, 19mm, Button Style, for 12000 to 20000mL Flasks, 725mm OAL
Stirring Shaft, 19mm, Button Style, for 12000ml. to 22000ml. Flasks, 725mm OAL. A 19mm OD precision ground stirrer shaft to fit CG-2082 and CG-2083 19mm bearings. Side button for attachment of CG-2089 PTFE stirrer blades.PLEASE NOTE: THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF PTFE BEARING. FOR POLISHED SHAFTS USED WITH PTFE BEARINGS SEE CG-2088. ALSO NOTE: 19MM SHAFTS HAVE A REDUCED DIAMETER TOP SECTION THAT IS 1/2"OD, PLEASE KEEP THIS IN MIND WHEN SELECTING THE PROPER SIZE COUPLING.
Chemglass Life Sciences Stirring Shaft, 19mm, Polished, Chem-Stir, 3 to 12L Flasks, 610mm OAL, Complete with PTFE Nut and Bolt
Stirring Shaft, 19mm, Polished, Chem-Stir, 3L-12L Flasks, 610mm OAL, Complete with PTFE Nut and Bolt. A 19mm OD precision ground and polished stirrer shaft with our patented Chem-Stir blade attachment system. Shaft (C) has been manufactured with a ring at the lower end to permit attachment of the blade (B) with a PTFE nut (D) and bolt (A). Shaft is supplied complete with PTFE nut and bolt set. For use with PTFE bearings such as the CG-2086. Polished shaft will not cause abrasion to the sealing surfaces of the PTFE bearing, thereby allowing a vacuum tight seal. Uses the same PTFE nut and bolt blade attachment method as the CG-2084 ground shaft.PLEASE NOTE: STIRRER BLADES MUST BE PURCHASED SEPARATELY.THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF GLASS BEARING. FOR GROUND SHAFTS USED WITH GLASS BEARINGS SEE CG-2084.ALSO NOTE: 19MM SHAFTS HAVE A REDUCED DIAMETER TOP SECTION THAT IS 1/2"OD, PLEASE KEEP THIS IN MIND WHEN SELECTING THE PROPER SIZE COUPLING.
Chemglass Life Sciences Stirrer Blade, PTFE, Banana Shape, Solid, 10mm, for 1000mL Flasks, 34/45 minimum joint clearance
Stirrer Blade, PTFE, Banana Shape, Solid, 10mm, for 1000mL Flasks, 34/45 minimum joint clearance. Blade is shaped to resemble the contour of a round bottom flask. Blades are solid. Made of 1/8" PTFE to fit 10mm OD stirrer shafts. Minimum joint size listed is the size required to allow passage of the blade.
Chemglass Life Sciences Agitator, Turbine, PTFE, 100mm Dia, Fits Shaft Size 10mm
Agitator, Turbine, PTFE, 100mm Dia, Fits Shaft Size 10mm. Agitators are made entirely of PTFE and glass filled PTFE and are for use with 10mm OD stirrer shaft CG-2075-B. Great for use a “foam breaker” at the liquid level in the reactor. Agitator hub is open so that it can be positioned anywhere along the stirrer shaft.
Chemglass Life Sciences 10mm Chem-Vac Stirrer Bearing, PTFE, 45/50 Joint Size
10mm Chem-Vac Stirrer Bearing, PTFE, 45/50 Joint Size. Chem-Vac PTFE stirrer bearing provides a VACUUM TIGHT FLAKE-FREE SEAL. Two versions of the bearing are available, the standard series for 2L and smaller vessel capacities and the stabilizer series that incorporates a PEEK/PTFE stabilizing bushing that is molded to the lower portion of the inner joint. The stabilizer greatly reduces stirrer shaft whip on larger vessels. The bearing consists of a PTFE standard taper body, Glass filled polypropylene screw cap, PEEK Compression spring, PEEK/PTFE sleeve and a glass filled polypropylene loosening nut. The polymer blend sleeve provides a long lasting seal for use up to 500 RPM. Loosening nut above the standard taper inner joint allows easy and quick removal. PLEASE NOTE: PTFE STIRRER SHAFTS ARE NOT RECOMMENDED FOR USE WITH THIS BEARING.
Chemglass Life Sciences Replacement 19mm Stirrer Shaft, Reactor Size: 15L-20L, Fits Support Frame: CG-1965-X-150, Overall Length: 34.6"
Replacement 19mm Stirrer Shaft, Reactor Size: 15L-20L, Fits Support Frame: CG-1965-X-150, Overall Length: 34.6". Precision ground and polished stirrer shaft for use with Chemglass process reactors. Designed to utilize CG-2095 and CG-2096 PTFE agitators. Lower portion of stirrer shaft is sandblasted and has a 3/8¿ wide flat. REPLACEMENT STIRRER SHAFTS ARE FOR USE WITH MECHANICAL SEAL STIR BEARING ON LISTED SUPPORT FRAME.
Chemglass Life Sciences 10mm Chem-Vac Stirrer Bearing, PEEK/PTFE Stabilizer, PTFE, 24/40 Joint Size
10mm Chem-Vac Stirrer Bearing, PEEK/PTFE Stabilizer, PTFE, 24/40 Joint Size. Chem-Vac PTFE stirrer bearing provides a VACUUM TIGHT FLAKE-FREE SEAL. Two versions of the bearing are available, the standard series for 2L and smaller vessel capacities and the stabilizer series that incorporates a PEEK/PTFE stabilizing bushing that is molded to the lower portion of the inner joint. The stabilizer greatly reduces stirrer shaft whip on larger vessels. The bearing consists of a PTFE standard taper body, Glass filled polypropylene screw cap, PEEK Compression spring, PEEK/PTFE sleeve and a glass filled polypropylene loosening nut. The polymer blend sleeve provides a long lasting seal for use up to 500 RPM. Loosening nut above the standard taper inner joint allows easy and quick removal. PLEASE NOTE: PTFE STIRRER SHAFTS ARE NOT RECOMMENDED FOR USE WITH THIS BEARING.