Electron Microscope Accessories
Electron Microscopy Sciences Hitachi M4 SEM Cylinder Mount 1-1/4" surface, 1/4" height, Aluminum
Hitachi M4 SEM mounts are made from lathe finished ultra-pure aluminum.
Head: 1-1/4
Pin height: 1/4"
Electron Microscopy Sciences Hitachi M4 SEM Cylinder Mount 1-1/4" surface, 3/8" height, Aluminum
Hitachi M4 Thread SEM mounts made from lathe finished ultra-pure aluminum.
Head: 1-1/4"
Height: 3/8"
Electron Microscopy Sciences SEM Mount Hitachi M4 1" Surface 9-Division, 1/4" height, Aluminum
Hitachi cylinder mount has a M4 tapered hole with female thread. Made from lathe finished ultra-pure aluminum. M4 tapered hole.
Head: 1"
Height: 6 mm
Electron Microscopy Sciences Standard Pin SEM Stub Slotted 18 mm Head with 8 mm Pin, Aluminum, 3.2 mm Pin diameter
Pin stub mount with slotted head for use with Cambridge, Leica, ZEISS/LEO, FEI/Philips, PHENOM, CamScan, and Tescan.
Head: 18 mm
Pin height: 8 mm
Electron Microscopy Sciences Shorter Pin SEM Stub Slotted 1/2" Head with Shorter Pin (6 mm), Aluminum, 1/8" Pin diameter
Cambridge, Phillips, Camscan, B&L, Etec, Zeiss SEM specimen mounts. Tapered end pin, slotted head.
Head: 1/2"
Pin height: 6 mm
Pin diameter: 1/8"
Electron Microscopy Sciences Metallurgical Mount Holder Hitachi M4
This mount holder which is made from machined aluminum with stainless steel Allen screws is specifically for 1" or 25 mm metallurgical mounts.
Electron Microscopy Sciences Metallurgical Mount Holder 1.5" and 40 mm, 3.2 mm x 8mm Pin
This set screw vice which is made from machined aluminum with stainless steel allen set screws has an open slot that is 10 mm (.394") wide x 5 mm (.197") deep. It measures 25 mm (1”) dia. x 17.5 mm (0.69”) high.
Type: 3.2 mm x 8 mm Pin
Electron Microscopy Sciences Hitachi M4, Hitachi M4
SEM specimen holder is 32 mm large double slot set screw vise with (2) 2.5 mm wide x 5 mm deep slots. Clamp thin specimens and cross sections. Machined aluminum with 2 stainless steel allen set screws. Includes allen wrench.
Type: Hitachi M4
Size: 32 mm
Electron Microscopy Sciences SEM Hitachi S-450 M4 Mount 3-Division 5/8", 1/4" height, Aluminum
Hitachi S-450 SEM mounts with M4 tapered hole and female thread. With 3 divisions. Made from ultra-pure aluminum with standard lathe finish.
Head: 5/8"
Height: 1/4"
Electron Microscopy Sciences Circlips Insertion Tool
Circlips are for all EMS TEM sample holders and specimen rods. They are made from heat treated Beryllium copper. The Circlip extraction tool is for removing our Circlips from all TEM sample holders.
Electron Microscopy Sciences Calibration Specimen 700-1D, Steel disk for AFM
SPM calibration specimens are produced by holographic fabrication that assures high accuracy and precision. The standards provide easier testing of your SPM, improved accuracy of critical dimension measurements and accuracy of 0.5% (1 std. dev.). The pattern height of greater than 100nm provides excellent image contrast. There is uniform coverage of entire chip which allows for imaging anywhere on the chip. Parallel Ridges Pitch 700, W-coated Photoresist on Si. Use contact or TappingMode.
Mount: AFM