Slide Mounting Media
Electron Microscopy Sciences Colloidal Silver Liquid, 15 g
1-Methoxy-2-propanol base. Fast drying. Average grain size less than 1 µm and Silver content is 60%. Sheet resistance is 0.02 ohm per square inch at 1 mil thickness. Comes with a brush attached to the cap. Service temperature is 30 minutes at 200°C.
Electron Microscopy Sciences EMbed-812 kit, 1 kit
Replacement for the discontinued Epon-812. Produces the same results in terms of preservation, handling, sectioning, and staining as the old Epon-812. Kit consists of 450 ml EMbed-812, 450 ml DDSA; Specially Distilled, 450 ml NMA, and *50 ml DMP-30. *Please note that wherever DMP-30 is listed as the accelerator in our embedding media kits you have the option to use BDMA in place of it. BDMA is less viscous, has a longer shelf life, and offers better penetration (it should be noted, however, that in order to achieve the optimum results when using BDMA in place of DMP-30 you must vary the amount. DMP-30: 1.5-2%; BDMA: 2.5-3%).
Electron Microscopy Sciences LR White Resin, Hard, Uncatalyzed 500 ML
A very low viscosity (8cps), non-toxic resin, suitable for both Light and Electron Microscopy. LR White is a polar monomer polyhydroxylated acromatic acrylic resin. It can be cured by heat or by UV light. Sections of polymerized LR White resin are hydrophilic. This character allows immuno-cytochemistry reagents to easily penetrate into the sections and etching of the sections is not necessary (etching sections will effect delicate tissue antigens). LR White sections also show minimal non-specific staining. Its low viscosity makes it ideal for infiltrating decalcified bone and teeth as well as plant tissues.
Electron Microscopy Sciences Technovit 8100 Embedding Kit
Technovit Glycol Methacrylate embedding kits developed by Kulzer in Germany are the most convenient to use and offers the best embedding results. Kits give better results offering improved morphology and allows for 1 micron serial sectioning. Polymerization temperature never exceeds 40 degree C, which makes either kit a potential choice for enzyme histochemistry.
The initiator is prepackaged, eliminating messy handling of dry components, and by eliminating aromatic amines from the formation, the components are significantly less toxic. The consistent high quality of raw materials used to make the resin allows for a permanent clear colorless block and, most important, reproducible results
Electron Microscopy Sciences Technovit H7100 – GMA kit
Technovit H7100 – GMA kit consists of: 500 ml Glycol Methacrylate monomer, 5 x 0.6g packs Hardener I, 40 ml Hardener II; Technovit Glycol Methacrylate embedding kits developed by Kulzer in Germany are the most convenient to use and offers the best embedding results. Kits give better results offering improved morphology and allows for 1 micron serial sectioning. olymerization temperature never exceeds 40 degree C, which makes either kit a potential choice for enzyme histochemistry. Technical Note: GMA resin-based products (Technovit 7100, 8100) should not be used when epoxy removal from specimens is required. There is no known method of GMA epoxy removal (including methoxide) that does not effectively render specimens unusable. Instead, MMA resin-based products such as Technovit 9100 should be selected.
Electron Microscopy Sciences Technovit 3040 Mounting Medium Kit
Technovit 3040 yellow is a fast curing methyl methacrylate-based resin, whose chemical composition warrants a firm, durable bond between Technovit and the specimen.
Technovit 3040 consists of two components–powder and liquid–allowing simple mixing, easy adherance to the specimen, and fast curing. For fixing the mount, a high viscous consistency is required(i.e. a mixing ratio of approximately 2-3 parts per volume powder: 1 part per volume liquid) has proven to be the most advantageous.
Electron Microscopy Sciences EMbed 812, 450ml
EMbed 812 has the same characteristics as Epon 812, physically, and provides the same results in preservation, handling, curing and sectioning. EMbed 812 may cause etching on selected plastics. All formulas for mixing and using Epon 812 can be applied to EMbed 812
Electron Microscopy Sciences Low viscosity embedding media kit, 1 kit
Provides excellent penetration for embedding biological tissues and rapid infiltration. Easy to prepare. The hardness is adjusted by changing the proportion of the flexibilizer (DER 736). The blocks have good trimming and sectioning qualities. Thin sections are tough under the electron beam. Kit consists of: 450 ml NSA, 225 ml ERL 4221 , 225 ml DER 736 , 25 ml DMAE.
Electron Microscopy Sciences Entellan Rapid Mounting Media 500 ML
Entellan is a rapid mounting media for microscopy. It can be used for long life preparations, without bubble formation at high ambient temperatures. Also for all dehydrated microscopic preparations. Cure time is 20 minutes at room temperature. It is colorless with an acid number less than 2.50 and a R.I. ND20 approx 1.49-1.5. (Contains xylene).
Master Lock BLUETOOTH & ELECTRONIC LOCKS
Silver. The Master Lock No. 5441EC Bluetooth Wall Mount Lock Box features a 3-1/4" (83mm) wide metal body for durability. Secure your home or business with the Master Lock Vault. Exterior dimensions: 5in (12.7cm) x 3-1/4in (83mmcm) x 2-5/16in (59mmcm). Shackle Length: 1-13/32in (36mm); Shackle Width: 1-13/16in (46mm)
Biotium Drop-n-Stain EverBrite™ Mounting Medium with DAPI
Drop-n-Stain EverBrite™ Mounting Medium with DAPI is wet-set antifade in a convenient dropper bottle for one step mounting and counterstaining. EverBrite™ protects fluorescent dyes from photobleaching, and is compatible with cyanine-based dyes like Cy dyes and Alexa Fluor 647. Unit size: 10 mL.
Perkin Elmer US LLC Adhesive Film Mount - Qty. 100
PerkinElmer offers a variety of sample holders and film mounts that are convenient, easy-to-use, and economical.