Embedding Accessories
Electron Microscopy Sciences Micro-Bed Embedding Resin 500 ML
Micro-Bed resin is a water-soluble resin, a mixture of acrylate and polyester resins. Universal embedding medium that may be used for light or electron microscopy.
Due to its non-crosslinking characteristics, its hydrophilic nature, and roughness of its section surface, it is excellent in preserving tissue structure, offers good results in immunolabeling, and stands up well to conventional stains.
In LM, tissues were stained with conventional histological stains (e.g.,hematoxylin-eosin) and embedded in Micro-Bed: results comparable with those provided on paraffin embedded tissues. Polychrome silver-based and cytochemical stains (e.g.,PAS) were also feasible. In TEM, images as good as those obtained with similar acrylic resins, (e.g., Lowicryl K4M), were obtained.
Supplied as a single component-ready to use pre-mixed resin. Micro-Bed can be polymerized by heat (55-65°C) or UV (365nm) at -10 to 20°C for 72 hours.
Leica Biosystems Metal Base Molds 15 x 15 x 6 mm (Pack of 10)
Reusable metal base molds used for forming embedding wax blocks in histology workflows. Each mold measures 15 x 15 x 6 mm and is supplied as a pack of 10. The molds fit standard tissue embedding cassettes and provide consistent block formation and efficient heat transfer.
- Reusable metal construction for repeated use.
- Internal rounded corners allow easy removal of formed wax blocks.
- Dimensions: 15 x 15 x 6 mm.
- Pack quantity: 10 per pack.
- Compatible with most standard tissue embedding cassettes.
- Provides rapid heat transfer for efficient wax setting.
Electron Microscopy Sciences 5 Block Embedding Mold-2 Part- 8 mm Body with 2 mm Cylindrical
The block embedding mold features an innovative new design based on the widely used Ø8 mm size embedding mold. The unique two part design allows for easy removal of resin blocks, as well as incorporating many other advantages over currently available embedding products.
It has separate base and tube sections that clip together to form the familiar capsule shape. It allows for easy removal of resin blocks achieved by simply pulling the mold apart by hand.
It can produce blocks up to 20 mm in length with no razor blades or capsule presses are required. Each mold can be clipped to other molds, allowing for the creation of trays of desired size. Each cavity is numbered 1 < 5, whilst the end support stands have designated areas for writing indexing numbers or comments.
Electron Microscopy Sciences Paraffin TMA ArrayMold F, Blue, 3.0 mm diameter, 35 cores per mold Capacity
The Arraymold is the simple tool for laboratories to perform Paraffin tissue microarrays (TMAs) w/ less time while maintaining excellent results. Process up to 150 specimens onto one single slide w/ very little time consuming, minimal tech training. The DVD is accompanying w/ each kit, will step by step guide you to perform through the entire TMAs process.
Arraymolds allow pathologist or researcher to view many different samples on the same single slide.
Helpful in finding IHC markers for control or quality assurance from hundreds of samples.
Staining markers will be more consistent when hundreds of samples are on one slide.
Used less costly antibody.
Arraymold kit is small enough to be stored in a drawer.
Rubber arraymold can be reused without losing flexibility. 10 Disposable 4mm sterile dermal needles, 2 Stylets, 1 Brass Plate, 1 4mm reusable rubber Arraymold, DVD.
Color: Blue
Diameter: 3.0 mm
Capacity: 35 cores per mold
Electron Microscopy Sciences Paraffin TMA Arraymold Kit 1 (A +B), 2.0 and 1.5 mm diameter
The Arraymold is the simple tool for laboratories to perform Paraffin tissue microarrays (TMAs) with less time while maintaining excellent results. Process up to 150 specimens onto one single slide with very little time consuming, minimal technical training. The DVD instruction is accompanying with each kit, will step by step guide you to perform through the entire TMAs process.
Arraymolds allow pathologist or researcher to view many different samples on the same single slide.
Helpful in finding IHC markers for control or quality assurance from hundreds of samples.
Staining markers will be more consistent when hundreds of samples are on one slide.
Used less costly antibody.
Arraymold kit is small enough to be stored in a drawer.
Rubber arraymold can be reused many times without losing its flexibility. This package includes two Arraymold kits, Kit A and Kit B.
Diameter: 2.0 and 1.5 mm
Electron Microscopy Sciences EBH-2 Microtome Block Holder, 6 mm
Block holder molded from hard plastic. Easy to store block holders attached to Aluminum chucks (ABH). Frosted surface for easy marking. Large center hole prevents bubble formation.
Size: 6 mm
Electron Microscopy Sciences Cold Embedding Silicone Mold for Acylic Resin 40 mm
This mold is for acrylic resins only and the best mounting cup for all of our acrylic resins. The flexible silicone rubber makes it very easy to remove the mount from the mounting cup.
Diameter: 40 mm
Electron Microscopy Sciences Flat Embedding Mold Flat Embed Mold Single End, 6 mm deep, 14 x 5 mm
A clear silicone rubber with very high tear strength. It can be reused more times than the conventional silicone molds. It is resistant to most epoxy resins and its clear base allows positioning of the specimen lighted from beneath. Standard flat embedding mold.
Depth: 6 mm
Size: 14 x 5 mm
Cavities: 21
Andwin Scientific CRYOMOLD 15X15X5
The Cryomold molds produce uniformly shaped, flat-surface specimen block when used with O.C.T. (optimum cutting temperature) compound, which is sold separately, for frozen sectioning. This can fit into Cryobar freezing wells of the Tissue Tek II microtome/cryostat with the use of an adapter. This product measures 15 mm x 15 mm x 15 mm.
Electron Microscopy Sciences T-Sue™ Microarray Mold Kit, 4 mm
T-Sue array molds are specifically designed to be simple, easy to use and inexpensive. The tissues can be analyzed in consistent conditions enhancing the efficiency of the research. Allow you to perform TMAs more quickly with excellent results. By using array molds, you can process up to 170 specimens onto one single slide in very little time.
Made of silicone, these molds can withstand temperatures between -100 deg C to +250 deg C and be reused hundreds of times without losing their flexibility.
Each kit includes one T-Sue array mold and four punch needles with stylet.
Size: 4 mm
Capacity: 15 cores