Embedding Accessories
Electron Microscopy Sciences Cold Embedding Silicone Mold for Acylic Resin 40 mm
This mold is for acrylic resins only and the best mounting cup for all of our acrylic resins. The flexible silicone rubber makes it very easy to remove the mount from the mounting cup.
Diameter: 40 mm
Polysciences, Inc. PolyPress™ Tissue Embedding Tampers (10mm x10mm)
This item has a minimum qty of 2 per supplier requirements.
Electron Microscopy Sciences Micro-Bed Embedding Resin 500 ML
Micro-Bed resin is a water-soluble resin, a mixture of acrylate and polyester resins. Universal embedding medium that may be used for light or electron microscopy.
Due to its non-crosslinking characteristics, its hydrophilic nature, and roughness of its section surface, it is excellent in preserving tissue structure, offers good results in immunolabeling, and stands up well to conventional stains.
In LM, tissues were stained with conventional histological stains (e.g.,hematoxylin-eosin) and embedded in Micro-Bed: results comparable with those provided on paraffin embedded tissues. Polychrome silver-based and cytochemical stains (e.g.,PAS) were also feasible. In TEM, images as good as those obtained with similar acrylic resins, (e.g., Lowicryl K4M), were obtained.
Supplied as a single component-ready to use pre-mixed resin. Micro-Bed can be polymerized by heat (55-65°C) or UV (365nm) at -10 to 20°C for 72 hours.
Electron Microscopy Sciences Lowicryl HM20 Monostep 225 GR
The same as our Lowicryl complete kits but this new formulation allows you one stop embedding without all of the cumbersome preparation and mixing. This pre-mixed, ready to use resin, saves you time and minimizes chemical contact. MonoStep Lowicryl is ideal for use in immunohistochemistry and immunolabeling. Store at room temperature.
Electron Microscopy Sciences Thompson Monolayer Embedding Mold
This mold used for embedding mammalian cells in monolayer culture in preparation of sectioning for light or electron microscopy. Tissue culture monolayer embedding molds eliminate the need for traditional BEEM capsules. The improved molds can be used to transfer the majority of cells from the entire surface of a cover slip to avoid losses of large amounts of cellular information occurring only randomly. In addition, other problems such as surface blemishes caused by air entrapment associated with BEEM capsules are eliminated.
Electron Microscopy Sciences EMS Molded Flat Embedding Mold
Molds are injected molded polyethylene that is resistant to most embedding materials and will easily peeled-off the blocks. Mold fits perfectly inside the cocoon box BE8 (64300-8). These molds are reusable. Each cavity measures 12mm(L) x 5mm(W) x 3.5mm Deep. Overall mold measures: 94 x 56 x 14mm.
Electron Microscopy Sciences Chien Universal-Mold
A two-directional mold that allows for single embedded specimens to be sectioned both laterally and transversely . Tissues to be embedded are accurately trimmed and placed so that both sides of the tissue are against both edges of the cavity tip. See Chien, K., et al. (1985) Proc. Ann. EMSA Meeting 43, 460
Electron Microscopy Sciences Slide Duplicating Mold, 3 Cavity
Uses a 1x3" glass slide as a base, and duplicates the slide using the resin of your choice. Tissue sections are embedded against the flat glass surface. This duplicated resin slide can be studied under the Light Microscope, then cut, remounted, resectioned, and studied under the EM. A three cavity mold, each cavity measuring: 1"(W)x3"(L)x3/32"(D). Reference and Instructions enclosed
Electron Microscopy Sciences Mold Release for Mounting Press 8 GR
Mold release agent to be used with mounting press.
Electron Microscopy Sciences Mold for Long Tissues
Accommodates longer pieces of tissues and makes it easy to embed long specimens and orient them properly. Tissues lie flat in the well. Ideal for any specimen that needs immediate sectioning (e.g. cell monolayer), 24 cavities