Embedding Cassettes and Storage
Electron Microscopy Sciences Cold Embedding Form Mold, 40 mm
The form mold is a two part mounting cup, designed to be as user-friendly as possible. It has practical handles for removing of the lid and the cylinder is slightly conical for easy removal of the mounts.
Diameter: 40 mm
Electron Microscopy Sciences Cold Embedding Form Mold, 1.5"
The form mold is a two part mounting cup, designed to be as user-friendly as possible. It has practical handles for removing of the lid and the cylinder is slightly conical for easy removal of the mounts.
Diameter: 1.5"
Electron Microscopy Sciences Cold Embedding Silicone Mold for Acylic Resin 32 mm
This mold is for acrylic resins only and the best mounting cup for all of our acrylic resins. The flexible silicone rubber makes it very easy to remove the mount from the mounting cup.
Diameter: 32 mm
Electron Microscopy Sciences Cold Embedding Silicone Mold for Acylic Resin 38 mm
This mold is for acrylic resins only and the best mounting cup for all of our acrylic resins. The flexible silicone rubber makes it very easy to remove the mount from the mounting cup.
Diameter: 38 mm
Electron Microscopy Sciences Cold Embedding Form Mold, 25 mm
The form mold is a two part mounting cup, designed to be as user-friendly as possible. It has practical handles for removing of the lid and the cylinder is slightly conical for easy removal of the mounts.
Diameter: 25 mm
Leica Biosystems PEACH CASSETTES 1000/CS
IP C Cassettes III are one-piece processing cassettes with a 35 degree writing surface. The cassettes are taped for easy loading into ink printers. Available in eleven colors in quantities of 1000.
Electron Microscopy Sciences LR White Resin Medium- Grade Kit
A very low viscosity (8cps), non-toxic resin, suitable for both Light and Electron Microscopy. LR White is a polar monomer polyhydroxylated acromatic acrylic resin. It can be cured by heat or by UV light. Sections of polymerized LR White resin are hydrophilic. This character allows immuno-cytochemistry reagents to easily penetrate into the sections and etching of the sections is not necessary (etching sections will effect delicate tissue antigens). LR White sections also show minimal non-specific staining. Its low viscosity makes it ideal for infiltrating decalcified bone and teeth as well as plant tissues. It is available in medium and hard grade. Kit consists of: 500 ml LR White Resin, 10 ml UV accelerator.
Electron Microscopy Sciences JB-4 Plus™ Embedding Kit
JB-4 Plus offers all of the same features as JB-4 except it produces less of an exothermic reaction than JB4 which is good for temperature sensitive tissues. J Kit consists 500 ml Solution A, 15 ml Solution B, 8 g Benzoyl Peroxide Catalyst.
Electron Microscopy Sciences Lowicryl K4M Monostep 225 GR
The same as our Lowicryl complete kits but this new formulation allows you one stop embedding without all of the cumbersome preparation and mixing. This pre-mixed, ready to use resin, saves you time and minimizes chemical contact. MonoStep Lowicryl is ideal for use in immunohistochemistry and immunolabeling. Store at room temperature.
Electron Microscopy Sciences JB-4™ Solution A 800 ML
A water soluble embedding media which is based on Glycol Methacrylate (GMA) plastic embedding. It is intended for use in preparing samples for high resolution microscopes (HRLM). The catalyzed monomer acts as a dehydration and infiltration agent; therefore, complete dehydration through 100% ethanol is not necessary (although recommended for large or dense tissues). Conventional paraffin sections have a greater degree of shrinkage and produce inadequate morphology when compared to JB-4.
Electron Microscopy Sciences Lowicryl HM20 Kit
Lowicryl resins are highly cross-linked acrylate-based embedding resins, designed for use over a wide range of embedding conditions. These resins provide low viscosity at low temperatures. All of these resins are photopolymerized by long wavelength (360nm) ultraviolet light. Since the initiation of the polymerization is largely independent of temperatures, blocks may be polymerized at the same temperatures used for infiltration. The resin may also be chemically polymerized at 60 degree C. Nonpolar (hydrophobic) usable to -70 C.
Electron Microscopy Sciences Gilder Hexagonal 200 mesh Gold Grid
A reliable support specimen grid source. Features: well-defined grid bars, maximum open area, and a matt/shiny side. Each grid is individually inspected. The copper grids with palladium plating offers better grid strength and avoids tarnishing. 3.05 mm diameter, 0.7 mil (18um) thickness.
Grid: Gold
Pitch: 125 µm
Hole: 100 µm
Bar: 25 µm
World Precision Instrument Celloger Stack
Celloger Stack is an automated multi-layer vessel monitoring system that enables real-time imaging of cell samples while they are cultured in an incubator. The system is capable of detecting cells growing in a multi-layer chamber and identifying the optimal time for cell harvest. With its motorized camera that can move in all directions, the system captures multiple points within the travel range which can be made into a time-lapse video with a simple click. NOTE: WPI is an authorized distributor of