Autosamplers and Injectors
Waters Corp Waters Vial Holder Tray, 12 Position, 10 mL
This product is a Vial Holder Tray designed to hold 12 vials, each with a 10 mL capacity. It is specifically for use with a 2707 Autosampler.
- Designed to hold 12 vials
- 10 mL capacity
- For use with a 2707 Autosampler
- Spare parts kits
- 1 unit per package
- Mechanical type
- HPLC system type
- As required replacement schedule
Waters Corp Waters Sample Loop, Ext. Hypo Tip, 5 μL
This sample loop is designed for precise fluid handling in laboratory environments. Featuring an extended hypo tip, it ensures accurate and reliable sample introduction.
- Features an extended hypo tip.
- Provides a 5 μL sample volume.
- Compatible with ACQUITY I-Class PLUS Sample Manager-FL system.
- Compatible with ACQUITY UPC2 SM-FL system.
Waters Corp Waters Performance Maintenance Kit, For 717 Autosampler, HPLC System
The Performance Maintenance Kit for the 717 Autosampler contains all the Quality Parts necessary to keep your instrument operating at peak performance.
- Contains all quality parts necessary to keep instrument operating at peak performance.
- Includes one seal pack replacement kit.
- Includes one syringe.
- Includes one filter insert assembly.
- Includes one 2.3 mm x 11.5 mm filter.
- Includes two 2 mm x 7 mm filters.
Waters Corp Waters Rheodyne 7725I Manual Injector, 1 to 20 μL, 6000 psi
A manual injector from Waters, model Rheodyne 7725I, with 316 stainless steel and TFE wetted materials, capable of 1 to 20 μL injections and rated for 6000 psi pressure.
- Wetted surface material includes 316 stainless steel and TFE.
- Enables sample injections from 1 μL to 20 μL without a loop change.
- Features a pressure limit of 6000 psi (420 kg/cm2).
- Syringe needle measures 2.0 in. (5.08 cm) in length and 0.028 in. (0.071 cm) in outer diameter (22 gauge).
Waters Corp Assembly, Drainage Tubing Guide, Maintenance Parts Kit
This product is an Assembly, Drainage Tubing Guide, which is categorized as a maintenance parts kit.
- Identified as a parts, drain tube guide.
- Part of maintenance parts and kits.
Waters Corp Capillary Tubing Assembly, ASM to Injection Valve
This capillary tubing assembly is designed for use in the nanoACQUITY UPLC system, connecting the Auxiliary Solvent Manager to the injection valve. It is crucial for proper system setup and priming procedures.
- Connects Auxiliary Solvent Manager to injection valve
- M-detail fitting attaches to bulkhead fitting (A1) outside flow controller box
- V-detail fitting attaches to port 5 of the sample manager’s injection valve
- Used for flushing A1-side-connection tubing during Auxiliary Solvent Manager priming
Restek™ Oven Flapper Assemblies
Ensure even and consistent column heating when the insulation becomes damaged or worn, for Agilent GCs
Restek™ Weldment Removal Tool for EZ Twist Top Split/Splitless Injection Ports
For quick removal of hot weldment without fingers touching hot surfaces
Restek™ EZ Twist Top Injection Port Kits
Change inlet liners faster and easier, for Agilent 5890/6850/6890/7820 GCs
Restek™ Replacement Insulation Gasket and Hardware Kit for Oven Flapper Assemblies
For Agilent 5890/6890 GCs
Waters Corp Sample Loop, 250 μL, Tubing Assembly
This sample loop tubing assembly is designed for use in chromatography systems, providing a precise sample volume for analysis.
- Connects the left valve (LV) CM-A Port 3 and Port 4.
- Features a 250 μL sample loop volume.
- Ensures proper system integration as a tubing assembly.
- 1
- 2