Embedding Accessories
Electron Microscopy Sciences EBH-2 Microtome Block Holder, 4 mm
Block holder molded from hard plastic. Easy to store block holders attached to Aluminum chucks (ABH). Frosted surface for easy marking. Large center hole prevents bubble formation.
Size: 4 mm
Electron Microscopy Sciences Molding Cup Tray, 5 mm height
These polyethylene trays are ideal for casting specimen blocks embedded with JB-4 or equivalents and are used with our block holders and chucks shown above.
Size: 6 x 12 mm
Height: 5 mm
Electron Microscopy Sciences Micro-Bed Embedding Resin 500 ML
Micro-Bed resin is a water-soluble resin, a mixture of acrylate and polyester resins. Universal embedding medium that may be used for light or electron microscopy.
Due to its non-crosslinking characteristics, its hydrophilic nature, and roughness of its section surface, it is excellent in preserving tissue structure, offers good results in immunolabeling, and stands up well to conventional stains.
In LM, tissues were stained with conventional histological stains (e.g.,hematoxylin-eosin) and embedded in Micro-Bed: results comparable with those provided on paraffin embedded tissues. Polychrome silver-based and cytochemical stains (e.g.,PAS) were also feasible. In TEM, images as good as those obtained with similar acrylic resins, (e.g., Lowicryl K4M), were obtained.
Supplied as a single component-ready to use pre-mixed resin. Micro-Bed can be polymerized by heat (55-65°C) or UV (365nm) at -10 to 20°C for 72 hours.
Electron Microscopy Sciences Easy-Molds™ for size 00 Capsules, 8 mm diameter
A newly designed mold which is convenient and offers better embedments. This tray-and-mold in one unit offers a unique specimen block that no other mold can. Each tray contains 2x10 block molds and measures 87x66 mm. Size 8mm diameter corresponds to capsule size "00" and forms a block face of 3mm.
Electron Microscopy Sciences Mold Release for Mounting Press 8 GR
Mold release agent to be used with mounting press.
Electron Microscopy Sciences Cold Embedding Silicone Mold for Acylic Resin 40 mm
This mold is for acrylic resins only and the best mounting cup for all of our acrylic resins. The flexible silicone rubber makes it very easy to remove the mount from the mounting cup.
Diameter: 40 mm
Electron Microscopy Sciences Cold Mounting Disposable Mold Cups, 1.5"
Mounting cups for cold mounting/embedding. Polyethylene, one part molds. Closed one end. Red.
Size: 1½"
Electron Microscopy Sciences Peel Away Disposable Embedding Mold Rectangular, 22 x 40 mm
Peel Away Disposable Embedding Molds are used for plastic or paraffin embedding. No block trimming needed. Inside fingers hold ID slip which becomes embedded in the block for positive permanent identification.
Size: 22 x 40 mm
Electron Microscopy Sciences Disposable Base Mold, 7 x 7 mm, 5 mm height
Our Disposable Base Mold is designed to fit all existing cassettes. Because our base molds are disposable you save time on cleaning and storing and they offer you less exposure to hazardous chemicals.
Size: 7 x 7 mm
Height: 5 mm
Electron Microscopy Sciences Easy-Load Cover for Biopsy Cassettes, Green
One-piece disposable plastic, it can be opened and closed as often as necessary and it always relocks securely without danger of specimen loss.
Color: Green
Electron Microscopy Sciences SupaMega Stainless Steel Slim Base Mold, 60 x 45 x 8 mm, 8 mm height
The SupaMega range of stainless steel base molds have extra deep side walls allowing wax to be decanted into the cassettes during embedding without the risk of the usual leakage of wax. The smaller faced mold also saves wax on medium sized blocks too large to fit into standard cassettes negating the use of full size molds.
Size: 60 x 45 mm
Height: 8 mm