Electron Microscope Specimen Mounts and Holders
Electron Microscopy Sciences Metallurgical Mount Holder 1 1/2" and 40 mm, Hitachi M4
This set screw vice which is made from machined aluminum with stainless steel allen set screws has an open slot that is 10 mm (.394") wide x 5 mm (.197") deep. It measures 25 mm (1”) dia. x 17.5 mm (0.69”) high.
Type: Hitachi M4
Electron Microscopy Sciences SEM Cylinder Mount 45° Angle 1" Surface, Aluminum
Scanning electron microscope specimen mount with 45 degree angle. Made from lathe finished ultra-pure aluminum.
Head: 1"
Height: 13/16"
Electron Microscopy Sciences Calibration Specimen 700-1D, Steel disk for AFM
SPM calibration specimens are produced by holographic fabrication that assures high accuracy and precision. The standards provide easier testing of your SPM, improved accuracy of critical dimension measurements and accuracy of 0.5% (1 std. dev.). The pattern height of greater than 100nm provides excellent image contrast. There is uniform coverage of entire chip which allows for imaging anywhere on the chip. Parallel Ridges Pitch 700, W-coated Photoresist on Si. Use contact or TappingMode.
Mount: AFM
Electron Microscopy Sciences Calibration Specimen 300-1D, SEM Pin
SPM calibration specimens are produced by holographic fabrication that assures high accuracy and precision. The standards provide easier testing of your SPM, improved accuracy of critical dimension measurements and accuracy of 0.5% (1 std. dev.). The pattern height of greater than 100nm provides excellent image contrast. There is uniform coverage of entire chip which allows for imaging anywhere on the chip. Parallel Ridges. Pitch 288 W-coated Photoresist on Si Use contact or Tapping Mode.
Mount: SEM Pin
Electron Microscopy Sciences Hitachi M4, Hitachi M4
SEM specimen holder is 32 mm large double slot set screw vise with (2) 2.5 mm wide x 5 mm deep slots. Clamp thin specimens and cross sections. Machined aluminum with 2 stainless steel allen set screws. Includes allen wrench.
Type: Hitachi M4
Size: 32 mm
Electron Microscopy Sciences Large Double Slot Set Screw Vise, 25 mm
SEM specimen holder with two 2.5 mm by 5 mm deep slots. Clamp thin specimens and cross sections without conductive paint or tape. 25 x 8 mm with 3.2 mm pin. Machined aluminum with 2 stainless steel allen set screws. Includes allen wrench.
Electron Microscopy Sciences Multi Holder for 29 pin Stubs, Hitachi M4
This 90 mm in diameter multi pin holder is designed to save time. It is made from machined aluminum with 302 stainless steel springs that hold the pin stubs in place. It accommodates up to twenty nine standard 12.7 mm (1/2") pin stubs
Type: Hitachi M4
Electron Microscopy Sciences SEM Cylinder Mount 45° Angle 1" Surface, Aluminum
Scanning electron microscope specimen mount with 45 degree angle. Made from lathe finished ultra-pure aluminum.
Head: 1"
Height: 13/16"
Electron Microscopy Sciences Variable Tilt Mount holder For Pin, 3.2 mm x 8mm Pin
This mount which is made from aluminum is used for the mounting and tilting of samples from 0 – 90 degrees as well as for SEM investigation with small working distances. The mount is marked for 30, 45, 70 and 90 degress. The table measures 11 x 11 mm (0.46" x0.46")and the overall size is 14 x 14 x12.7 mm
Type: 3.2 mm x 8mm Pin
Electron Microscopy Sciences Shorter Pin SEM Stub Slotted 1/2" Head with Shorter Pin (6 mm), Aluminum, 1/8" Pin diameter
Cambridge, Phillips, Camscan, B&L, Etec, Zeiss SEM specimen mounts. Tapered end pin, slotted head.
Head: 1/2"
Pin height: 6 mm
Pin diameter: 1/8"